|
|
|
Cavalier, Ecotec, Sunfire & S10
Performance &
Custom Engine Parts |
Email Us
(985) 956-7009
| Order ONLINE Anytime! |
|
|
| Camshafts |
IPP/WebCam Camshafts
Stage 1 - 4, Stage 5 Turbo & Stage 6 ULTIMATE Camshafts
Chevy Cavalier 2.2, Pontiac Sunfire, Chevy S10 ('94-02 VIN 4)
OUR CAMSHAFTS
We have an exclusive distributorship with Web-Cam (a
premier cam MFG in the US), and have designed a line of
cams for your Chevy Cavalier, Sunfire and S10 engine.
These are NEW CAMS with NO cam cores required!!!
All cams have been designed for ABOVE STOCK
PERFORMANCE (and Stages 1-3 do NOT
require spring replacement). These cams increase performance and
are for street on gas & Turbos.
These are brand new cams (vs. some competitors who sell
non-reground used cams), with the correct stock base circle.
You won't have to use shims, expensive buckets or lash caps!
(Note: The
figures below may vary slightly as cams have not been degreed in actual
motors at this time.)
REQUIREMENTS
Stage3+ up requires 7500 springs
(OEM valve springs can only handle so much valve lift before
they enter coil bind. This is where the spring has no more room
to compress. In other cases, the OEM valve spring cannot control
the valve properly, and valve float can occur. With a
performance or racing valve spring kit, there are fewer coils
(in most cases) and more room between the coils, allowing the
spring to compress more, in turn allowing for more valve lift,
while keeping the valve under control).
ADD-ONS
DTS2 Performance CNC Billet Aluminum
Lifter Guides (with more
room to allow for higher lift camshafts and stronger to provide
better lifter control especially at higher RPM's)
CUSTOM GRIND
We will custom grind these cams to your specifications. Add
only $20 to prices below.
Special Order only. Please call to order if you would like a Custom
Grind. 603.378.0090
IMPORTANT INFO on CAM HARDENING!
Cavalier camshafts have a very
thin hardening from the factory. When you get a cam reground,
unless you pay for additional hardening (which runs about an
extra $100), you have taken all the hardening out of the cam,
and it will not last long. Please understand that is why we
offer NEW cams that are hardened!
INSTALLATION INFO
Years '97 and below: You will need to cut the spring pockets
.100 for the heads to install our valves.
Years '98 and later: You may have to change pushrod length
depending on the cam lift. Contact our
Tech Dept. if you have questions.
WARRANTY
Our Webcam/IPP Camshafts are
warranted for 6 months only with the use of our
Beehive Springs.
(not warranteed if our proper
Beehive Springs are not
used).
IMPORTANT When PURCHASING
Adding Performance Lifters is
crucial when purchasing these performance Cams. Not only will
Performance Lifters add additional
power, but lifters should always be changed out
when installing a new cam as the stock ones are made in China
and do not last.
Are You
Sending In Your Cam Core?
DOWNLOAD
our worksheet to include w/your shipment. |
|
Stages 1 - 5, Turbo &
ULTIMATE Camshafts |
| Cam Description |
Valve |
Lash |
Valve
Lift |
Valve
Lift Dur. |
Cam Lift |
Duration @ .050 |
Part # |
Price |
Order
Now |
Stage
#1
w/1.6 Rocker, Lobe Separation 112
Good idle for daily use. Improved low to mid range torque.
Use stock springs and retainers. Stock compression OK, but will
work better with increased compression. |
INT |
000 |
438 |
262 |
274 |
202 |
11-002 |
$339.99 |
|
| EXH |
000 |
454 |
268 |
284 |
208 |
Stage
#2
w/1.6 Rocker, Lobe Separation 112
Good idle, more duration (keeps valves open longer), strong
pulling cam for improved mid and upper end power. Stock springs
& retainers can be used with stock compression, however the cam
needs more compression (10-1, 10.5-1), to make more HP (works
well for oval track with high compression). |
INT |
000 |
450 |
264 |
284 |
208 |
11-012 |
$349.99 |
|
| EXH |
000 |
465 |
274 |
293 |
212 |
Stage
# 3
(Non-Turbo)
w/1.6 Rocker, Lobe Separation 112
Slight idle (requires high compression and larger
bore pistons from stock bore, suggested 10.5-10.8 and
90mm bore), more duration (keeps valves open longer), strong
pulling cam for improved mid and upper end power. Stock springs
& retainers can be used with stock compression, however the cam
needs more compression (10-1, 10.5-1), to make more HP (works
well for oval track with high compression).
NOTES
New Lifters should be
changed out.
REQUIRED:
7500 Beehive Valve
Springs
*Top performer in upper middle to over 7500 RPMS (must
use spring 12-001 to 6500 or spring
12-002 for 7500 RPMS)
Listen to our Stage 3
Camshaft in Action!!! |
INT |
000 |
502 |
258 |
314 |
218 |
11-052 |
$349.99 |
|
| EXH |
000 |
516 |
265 |
323 |
226 |
Stage # 4
(Oval Track Only)
Lobe Separation
This cam is designed for the Oval Track Racer only,
for tons of power gain and high rpms, must have 11+
compression (the higher the better), requires our
Beehive Springs #12-001 or #12-002, for the correct spring
pressures. Stock retainers and locks can be used.
NOTES:
Check installed height and coil bind.
For best results lighter pistons &
rods (larger
valves
are a plus).
REQUIRES: 7500 springs |
INT |
- |
515 |
290 |
323 |
232 |
11-072 |
$349.99 |
|
| EXH |
- |
515 |
296 |
323 |
238 |
Stage # 5
(Turbo)
Lobe Separation 110
Designed specifically for Turbo or Supercharger Applications.
Legal for track use only.
Installed height for these are 1.7 |
INT |
- |
462 |
233 |
307 |
212 |
11-022 |
$329.99 |
|
| EXH |
- |
462 |
233 |
289 |
212 |
Stage #6 ULTIMATE!!!
The ABSOLUTE Ultimate HP for your 2.2 Cavalier!!!
We are now offering Mechanical camshafts and roller
lifters, for crazy street or drag and oval track racing.
These cams make tremendous power, with over 600 lift
ranges. Cams can be used with fuel injection or carbs.
There is not a Hydraulic cam that can match the lift,
duration and ramping for faster opening and closing of
valves than a mechanical roller. Adjustments will have
to be added to the ECU, or stand alone systems for
injected models. Engines using carbs will require less
electronics for installation. These cams are for the
ultimate HP for the 2.2 cavaliers.
REQUIRES: 7500 springs
PRICING: ULTIMATE Cam & Lifters = $1299.99
ORDER YOURS:
Please call our Sales Dept. at (985) 956-7009
(these cams are special order and can take 6-8 weeks
for delivery) |
|
| |
|
|
| |
| |
| |
|
|
HOME l
PERFORMANCE PARTS l
ENGINE
KITS l
CUSTOM PARTS l
AUTO RESOURCES l
CONTACT
Copyright 2010-2016
website design by
603 Design |
|
